UPDATE: Pipe Piece Blamed In BP Oil Probe - Spokane, North Idaho News & Weather KHQ.com

UPDATE: Pipe Piece Blamed In BP Oil Probe

NEW ORLEANS (AP) - The blowout preventer that should have stopped the BP oil spill failed largely because of a faulty design and a trapped piece of pipe, an official probe found Wednesday, appearing to shift some blame for the blowout from the oil giant and toward those who built and maintained the 300-ton safety device.

A 551-page investigative report said the piece of drill pipe prevented the blowout preventer's blind shear rams from sealing the well around the time of the April 20 oil rig explosion off the coast of Louisiana. The shear rams are components in a blowout preventer that cut, or shear, through drill pipe and form a seal against well pressure.

The drill pipe's position within the wellbore caused it to buckle and bow when the well lost control, impeding the rams, according to the report. The Norwegian firm hired by the government to test the blowout preventer also faulted the performance and design of the failsafe device.

Det Norske Veritas's report doesn't single out any one party involved in the well, but discusses in great detail why the device didn't work. The device was made by Cameron and maintained by Transocean Ltd.

BP, Cameron and Transocean did not immediately respond to requests for comment on the report.

Speculation on why the blowout preventer failed has persisted during the year since the disaster.

Documents emerged early in the probe showing that a part of the device had a hydraulic leak, which would have reduced its effectiveness, and that a passive "deadman" trigger had a low, perhaps even dead, battery.

DNV noted loss of fluid and weak battery issues in its report, but did not seem to cite them as significant causes of the blowout preventer's failure.

Philip Johnson, a University of Alabama civil engineering professor, said the report indicates that the blowout preventer had a design flaw in its blind shear rams that may have gone unnoticed by the entire industry, not just by Cameron.

"This is the first time in all of this that there has been a clear design flaw in the blowout preventer cited," he said. "My reaction is, "Holy smokes, every set of blind shear rams out there may have this problem.' We need to take a look at every set of blind shear rams out there and make sure they all don't have this problem."

"There are plenty of lawyers out there that are going to try to make this Cameron's fault, but I couldn't help (the lawyers)," he added.

The firm made several recommendations for the industry in its report, including changing the design of blowout preventers.

The firm's tests also indicated that some back-up control system components did not perform as intended. It recommended the industry revise its procedures for periodic testing and verification of the back-up control systems to assure they will function properly at all times.

Blowout preventers sit at the wellhead of exploratory wells and are supposed to lock in place to prevent a spill in case of an explosion.

The device that was used with BP's Macondo well was raised from the seafloor Sept 4. Testing began at a NASA facility in New Orleans in November.

Representatives for Cameron and Transocean were among an army of interested parties that were allowed to monitor DNV's examination of the device. BP, the Justice Department and lawyers for plaintiffs in lawsuits over the disaster also were allowed to monitor. None of them was allowed to have any hands-on involvement.

The official testing ended earlier this month. BP has asked a federal judge for permission to conduct additional testing on its own. Cameron has objected, saying that if further testing is done, a neutral third-party should do it.

An investigation into what caused the rig explosion and oil spill is being overseen by a joint U.S. Coast Guard-Bureau of Ocean Energy Management Regulation and Enforcement panel. While DNV's report was largely limited to results of its blowout preventer testing, the government panel is scheduled to release a final report over the summer assigning blame for the disaster.

  • Most Popular StoriesMost Popular StoriesMore>>

  • One man dead, another arrested after shooting near Post Falls

    One man dead, another arrested after shooting near Post Falls

    Sunday, October 21 2018 10:57 AM EDT2018-10-21 14:57:39 GMT

    POST FALLS, Idaho - Kootenai County Deputies arrested a man for involuntary manslaughter after they say he shot and killed another man Saturday evening near Post Falls. Deputies responded to reports of a shooting on Gallatin Way near Post Falls just before 7 pm. Deputies and medical personnel arrived and found a man, identified as Tyler S. Liles, with a single gunshot wound.

    >>

    POST FALLS, Idaho - Kootenai County Deputies arrested a man for involuntary manslaughter after they say he shot and killed another man Saturday evening near Post Falls. Deputies responded to reports of a shooting on Gallatin Way near Post Falls just before 7 pm. Deputies and medical personnel arrived and found a man, identified as Tyler S. Liles, with a single gunshot wound.

    >>
  • Spokane Police arrest suspect from hit-and-run crash on South Hill

    Spokane Police arrest suspect from hit-and-run crash on South Hill

    Sunday, October 21 2018 12:51 AM EDT2018-10-21 04:51:56 GMT

    SPOKANE, Wash. - Spokane Police have successfully located and arrested a suspect from a hit-and-run incident on the South Hill Saturday morning. After crashing a Corvette into an SUV near 53rd and Regal, 36-year-old Kristopher Riley fled the scene on foot and left his passenger inside the vehicle. Police say the passenger of the Corvette and driver of the SUV were hospitalized with serious injuries.

    >>

    SPOKANE, Wash. - Spokane Police have successfully located and arrested a suspect from a hit-and-run incident on the South Hill Saturday morning. After crashing a Corvette into an SUV near 53rd and Regal, 36-year-old Kristopher Riley fled the scene on foot and left his passenger inside the vehicle. Police say the passenger of the Corvette and driver of the SUV were hospitalized with serious injuries.

    >>
  • Spokane Police searching for suspect in early morning downtown stabbing

    Spokane Police searching for suspect in early morning downtown stabbing

    Sunday, October 21 2018 10:35 AM EDT2018-10-21 14:35:46 GMT

    SPOKANE, Wash. - One person was taken to the hospital after being stabbed in downtown Spokane early Sunday morning and police are still looking for a suspect.  Spokane Police say they received a report of a stabbing near Sprague and Washington just before 1 am on Sunday. Arriving officers found a man who had been stabbed in a parking lot near the intersection.  

    >>

    SPOKANE, Wash. - One person was taken to the hospital after being stabbed in downtown Spokane early Sunday morning and police are still looking for a suspect.  Spokane Police say they received a report of a stabbing near Sprague and Washington just before 1 am on Sunday. Arriving officers found a man who had been stabbed in a parking lot near the intersection.  

    >>
HD DOPPLER 6i
/