Extreme Science: Pendulum Drop - Spokane, North Idaho News & Weather KHQ.com

Extreme Science

Extreme Science: Pendulum Drop

Posted:

Join us every Saturday morning for Extreme Science with Radical Rick.

This week Rick shows us the "Pendulum Drop".

Here's what you need for this experiment:

  1. Shoestring or similar type and length of string or yarn
  2. Scissors
  3. 16 medium size hex nuts or washers
  4. Pencil
  5. Adult supervision

Procedure:

  1. Tie one hex nut (or washer) to one end of your string.
  2. Make a 2-3" loop in the other end of your string and tie this off
  3. Thread your string (looped end) through all but one of your remaining hex nuts.
  4. Thread the looped end of the string through the last hex nut so that the loop is sticking out about 2 inches. Open up the loop and pull this hex nut through the loop and pull the string tight to secure it in place.
  5. Hold your index finger (or a pencil) out and place the string over your extended index finger.
  6. Holding onto the single hex nut, pull the string horizontally bringing the large group of hex nuts up so that they are almost touching your finger.
  7. With the single hex nut being held level with your extended index finger, let go of the end with the single hex nut and watch what happens!

What is going on?

A pendulum is a weight that is suspended from a fixed point that swings back and forth due to the force of gravity. When you release the single hex nut, common sense tells us that, since the other end of the string is so much heavier, gravity will pull it towards the floor pulling the single hex nut over the top of your finger and to the floor below. We must remember that gravity is also pulling on the single hex nut causing it to accelerate towards the ground when we release it. Since the length of the string between your finger and the single hex nut is rapidly decreasing the velocity of your pendulum increases which in turn increases the amplitude causing the string to wrap around your finger several times.

Try this:

  • Try adding more hex nuts to the heavier end of the string. You can easily do this by pulling the loop back over the single hex nut, string more hex nuts on and loop the string around the last one securing it in place again.
  • How much weight can you add to the heavy end and still have it work?
  • How many can you take off and still have it work? Would this work with something as light as a feather on the light end of the string?
  • What happens if you change the length of the string?
  • Most Popular StoriesMost Popular StoriesMore>>

  • Family's Car Catches Fire Inside Lion Enclosure

    Family's Car Catches Fire Inside Lion Enclosure

    Sunday, April 20 2014 2:57 PM EDT2014-04-20 18:57:30 GMT
    (NBC)- A British family was forced to flee their car inside a lion enclosure, after the vehicle caught fire. Other visitors shot amateur footage of the car on fire. Helen Clements, who was in the car with her two children, said they were caught between wanting to escape the burning car while evading the lions.>>
    (NBC)- A British family was forced to flee their car inside a lion enclosure, after the vehicle caught fire. Other visitors shot amateur footage of the car on fire. Helen Clements, who was in the car with her two children, said they were caught between wanting to escape the burning car while evading the lions.
    >>
  • BEAUTIFUL HOMES: Top 10 Most Expensive Homes For Sale In CDA

    BEAUTIFUL HOMES: Top 10 Most Expensive Homes For Sale In CDA

    Tuesday, March 25 2014 9:20 AM EDT2014-03-25 13:20:34 GMT
    KHQ.COM - When it comes to shopping around for a house, it's always fun to dream. We did a search for some of the most expensive homes for sale right now in the Coeur d' Alene area.>>
    KHQ.COM - When it comes to shopping around for a house, it's always fun to dream. We did a search for some of the most expensive homes for sale right now in the Coeur d' Alene area.>>
  • Organizers With The Seafair Torchlight Parade Issue An Apology

    Organizers With The Seafair Torchlight Parade Issue An Apology

    Sunday, April 20 2014 10:47 PM EDT2014-04-21 02:47:17 GMT
    SPOKANE, Wash. - This year the Fallen Hero Banner project, which honors men and women from Washington who have died serving our country, applied to march in the Seafair Torchlight Parade in Seattle. However, the organization was denied by the parade selection committee via email saying, "the Fallen Hero Banner Project was not the right fit for the Torchlight Parade.">>
    SPOKANE, Wash. - This year the Fallen Hero Banner project, which honors men and women from Washington who have died serving our country, applied to march in the Seafair Torchlight Parade in Seattle. However, the organization was denied by the parade selection committee via email saying, "the Fallen Hero Banner Project was not the right fit for the Torchlight Parade.">>